Ford tractor parts ... Call us today ... 1-502-532-7988 ... or use our Information Request Form.

Used Equipment LandTrac Land Pride Tufline Toys Our Location E-mail us Home

Why should you buy a LandTrac? The flat deck design, comfortable seat, and smooth syncromesh transmission make the Landtrac a joy to operate. The Landtrac has dual remote valves plus many other standard features not found on the competition. LandTrac offers: Proven performance with 4 cylinder Mitsubishi engines from 41-53 engine horsepower Syncromesh transmissions with shuttleshift and creeper gears as standard equipment Flat deck system for easy entry Dual remote valves are standard PTO selector, with a switch to choose independent or manual operation (when needed). Position and draft control are standard equipment Brawny, well balanced, designed tractor built for superior pulling and lift capacity wrapped up in an ergonomically designed package	Pay Special Attention To LandTracs': Exceptional fit and finish Ergonomic design Ease of service Formula for satisfaction:  Quality + Price = VALUE
	These powerhouses feature: High efficiency, long stroke, Mitsubishi 4 cylinder diesel engine. These engines are known worldwide for exceptional quality Indirect (swirl chamber) injection. These designs produce lower emissions, less noise, less vibration and less engine stress resulting in longer engine life. Denso inline injection pump: A name known for performance. State of the art, fuel filtering system: includes an electronic sensor to indicate restrictions or contaminants in the system With removable panels and a pop-up hood, all engine service points are accessible for easy maintenance. Dual stage "Dry" type air cleaner is simple and easy to service. "Spin-on" oil filtering system changes simply and quickly
Engine: EPA Approved, 141 cubic inch displacement on the LandTrac 410 DTC. The 470 and 530 DTC models feature EPA approved 153 and 203.3 cubic inch displacements respectively.
Transmission (16 Forward/16 Reverse Speeds): Fully synchronized speed and range transmission for smooth operation Standard shuttle-shift delivers high performance loader operations.  This dash mounted forward/reverse shifting reduces cycle time and increases family time. Standard creeper gear gives you more low speed choices for specialty operations. Independent PTO with Electro-hydraulic  clutch for long life and reliability Spring loaded differential lock is foot controlled. Smooth operating 2/4 wheel drive selector is ergonomically located between the seat and fender. Dry single disc clutch uses time proven design delivers reliable performance.	Final Drives: Spur (or "bull") gear final drive: provides lower ground clearance and heavy duty operation Independent, wet, multi-disc brakes. Completely waterproof. Steering: Hydrostatic power steering utilizes "feather touch" steering regardless of terrain or load Independent hydraulic steering pump Front axle steering operates on a single heavy duty hydraulic cylinder Practically all critical parts are enclosed reducing the risk of damage and ensuring smoother operation
Standard Electrical Accessories Horn Hazard lights Headlights Rear work light 7 terminal receptacle for remote electrical hookup of trailers or implements Electrical System Information Indicators Battery charging system malfunction light Power take off light lets the operator know the PTO is in operation Glow plug time out indicator lets the operator know when it’s safe to start the engine during cold starts Engine oil pressure warning light Hydraulic oil filter restriction warning light Electrical System Gauges and meters Tachometer monitors revolutions per minute on engine shaft Fuel level gauge Hour meter Engine temperature gauge	PTO: Electro-hydraulic switch is located on the dash. Choose between manual or automatic operation: Manual position: The PTO stops rotating when the main clutch pedal is depressed. Useful when you need to stop the PTO engaged implement and tractor at the same. time Automatic position: The PTO runs independent of the main clutch. Especially useful when operating a loader with an independent hydraulic system or other various implements. Fully independent operation for consistent implement operation. Results in less stress on the implement and the tractor. Multiple wet clutch for the PTO power line for extremely smooth operation
Hitch System: Mixed draft and position control system as standard equipment. This feature automatically regulates the working depth of your implements, increasing performance and efficiency. Turn handle adjustments on bottom hitch points simplify implement hookup Versatile Category I and II hitch
	Hydraulic System: Open center engine mounted gear pump Dual remote valves (operator can select single acting) 8.8 to 9.5 gallons per minute pump capacity Hydraulic flow control lets the operator manageable implement control to the job. ISO Quick disconnect couplings for easier hose hookup
Ergonomics: Flat deck system makes getting on and off the LandTrac easier and improves operators comfort level while in operation. Sloping hood design improves field of vision for the operator. Easily accessible controls: All operating levers are in close proximity to the operator utilizing natural motion to improve comfort. Deluxe integrated instrument panel: Operator can easily monitor critical engine parameters.
Top features that make the LandTrac Utility tractors user friendly
Front lifting hood design Easy access oil check point Easy access engine oil fill point Easy access battery area Easy access oil drain plug Easy access radiator check point Easy access fuel tank fill point Turn handle on lower hitch point for adjusting attitude of hitch Synchronized main gear shifter Shuttle shifter on steering column Spring loaded rear differential lock Conveniently place remote valve levers Comfortable, adjustable seat Electrical PTO selection lever on dash Folding ROPS Wide flat deck increases leg room Easily monitored integrated dash Headlights Rear working lights Shuttle shift transmission (standard) Creeper gear (standard)

LandTrac 280 DTC Specifications
Engine	Mitsubishi Indirect Injection Diesel Engine
Engine Horsepower	28 HP
Number of cylinders	4
Bore and Stroke	3.07" X 3.09"
Total Displacement	91.5 cubic inches
Rate Speed (rpm)	2600
Fuel Tank Capacity	10 gallons
Cold Weather Starting	Glow Plugs
Air Cleaner	Dry Type with Replaceable Cartridge
Power Take Off	540 RPM
PTO Horsepower	27
Operation	Independent or Manual/ Switch Operated
PTO Clutch	Electro-Hydraulic, Operated by switch on dash Panel
Shaft Diameter	1 3/8" (Six Spine)
Hydraulic System	Open Center
Flow gpm/psi	6 gpm/ 2400 psi
Lift Capacity	2976 lbs. @ 24" behind lower hitch pins
3 pt. Hitch Category	I
Controls	Position / Draft / Mixed
Remote Value (standard)	Double Spool/Double Acting -- with two sets of outlets
Transmission	12 Forward - 6 Reverse
Main Gear Shift	Full Synchronized 4 speeds
Range Selector	Sliding Gear, 3 Ranges (Slow - Medium - Fast)
Shuttle Selector	Synchronized, Forward - Reverse
Forward Speed Range	.4 - 12.6 MPH
Clutch	9.5" Dry Single Disc
Steering	Full Hydrostatic
Brakes	L & R Independent Oil Immersed Disc Brakes Parking Brake: Operated off of service brake
Differential Lock (rear)	Foot Actuated - Mechanical
Electrical System         Alternator	12V - 50 Amp
Battery	12V, 600 CCA
General Specifications	Dimensions with Standard Tire
Turning Radius	99.2" with brake/ 113.8" without brake
Length	126"
Width	51.3"
Height to top of ROPS	88"
Wheel Base	63"
Tire Sizes (Front/Rear)	8.3 x 16 (4 ply) / 12.4 x 24 (8 ply)
Weight with ROPS	3100 lbs.
Options	Front Weights

 

LandTrac 360 DTC Specifications
Engine	Mitsubishi Indirect Injection Diesel Engine
Engine Horsepower	36 HP
Number of cylinders	4
Bore and Stroke	3.07" X 3.09"
Total Displacement	107.3 cubic inches
Rate Speed (rpm)	2700
Fuel Tank Capacity	10 gallons
Cold Weather Starting	Glow Plugs
Air Cleaner	Dry Type with Replaceable Cartridge
Power Take Off	540 RPM
PTO Horsepower	33
Operation	Independent or Manual/ Switch Operated
PTO Clutch	Electro-Hydraulic, Operated by switch on dash Panel
Shaft Diameter	1 3/8" (Six Spine)
Hydraulic System	Open Center
Flow gpm/psi	6 gpm/ 2400 psi
Lift Capacity	2976 lbs. @ 24" behind lower hitch pins
3 pt. Hitch Category	I
Controls	Position / Draft / Mixed
Remote Value (standard)	Double Spool/Double Acting -- with two sets of outlets
Transmission	12 Forward - 6 Reverse
Main Gear Shift	Full Synchronized 4 speeds
Range Selector	Sliding Gear, 3 Ranges (Slow - Medium - Fast)
Shuttle Selector	Synchronized, Forward - Reverse
Forward Speed Range	.5 - 14.5 MPH
Clutch	9.5" Dry Single Disc
Steering	Full Hydrostatic
Brakes	L & R Independent Oil Immersed Disc Brakes Parking Brake: Operated off of service brake
Differential Lock (rear)	Foot Actuated - Mechanical
Electrical System        Alternator	12V - 50 Amp
Battery	12V, 600 CCA
General Specifications	Dimensions with Standard Tire
Turning Radius	99.2" with brake/ 113.8" without brake
Length	126"
Width	51.3"
Height to top of ROPS	88"
Wheel Base	63"
Tire Sizes (Front/Rear)	8.3 x 16 (4 ply) / 12.4 x 24 (8 ply)
Weight with ROPS	3100 lbs.
Options	Front Weights

 

LandTrac 410 DTC Specifications
Engine	Mitsubishi Indirect Injection Diesel Engine
Engine Horsepower	41 HP
Number of cylinders	4
Bore and Stroke	3.46" X 3.74"
Total Displacement	141 cubic inches
Rate Speed (rpm)	2600
Fuel Tank Capacity	14.5 gallons
Cold Weather Starting	Glow Plugs
Air Cleaner	Dry Type with Replaceable Cartridge
Power Take Off	540 RPM
PTO Horsepower	38
Operation	Independent or Manual/ Switch Operated
PTO Clutch	Electro-Hydraulic, Operated by switch on dash Panel
Shaft Diameter	1 3/8" (Six Spine)
Hydraulic System	Open Center
Flow gpm/psi	8.8 gpm/ 2400 psi
Lift Capacity	2976 lbs. @ 24" behind lower hitch pins
3 pt. Hitch Category	II
Controls	Position / Draft / Mixed
Remote Value (standard)	Double Spool/Double Acting -- with two sets of outlets
Transmission	8 Normal / 8 Creeper Forward -- 8 Normal / 8 Creeper Reverse
Main Gear Shift	Full Synchronized 4 speeds
Range Selector	High - Low
Creeper Gear	Selector located on left of platform
Shuttle Selector	Synchronized, Forward - Reverse
Forward Speed Range	.1 - 12.9 MPH
Clutch	10.83" Dry Single Disc
Steering	Full Hydrostatic
Brakes	L & R Independent Oil Immersed Disc Brakes Parking Brake: Operated off of service brake
Differential Lock (rear)	Foot Actuated - Mechanical
Electrical System        Alternator	12V - 50 Amp
Battery	12V, 600 CCA
General Specifications	Dimensions with Standard Tire
Turning Radius	114.9" with brake/ 133.9" without brake
Length	137"
Width	61.8"
Height to top of ROPS	93"
Wheel Base	72.8"
Tire Sizes (Front/Rear)	8.3 x 20 (6 ply) / 12.4 x 28 (6 ply)
Weight with ROPS	4440 lbs.
Options	Canopy, Front Weights

LandTrac 470 Specifications
Engine	Mitsubishi Indirect Injection Diesel Engine
Engine Horsepower	47 HP
Number of cylinders	4
Bore and Stroke	3.46" X 4.05"
Total Displacement	153 cubic inches
Rate Speed (rpm)	2700
Fuel Tank Capacity	14.5 gallons
Cold Weather Starting	Glow Plugs
Air Cleaner	Dry Type with Replaceable Cartridge
Power Take Off	540 RPM
PTO Horsepower	41
Operation	Independent or Manual/ Switch Operated
PTO Clutch	Electro-Hydraulic, Operated by switch on dash Panel
Shaft Diameter	1 3/8" (Six Spine)
Hydraulic System	Open Center
Flow gpm/psi	9.2 gpm/ 2400 psi
Lift Capacity	2976 lbs. @ 24" behind lower hitch pins
3 pt. Hitch Category	II
Controls	Position / Draft / Mixed
Remote Value (standard)	Double Spool/Double Acting -- with two sets of outlets
Transmission	8 Normal / 8 Creeper Forward -- 8 Normal / 8 Creeper Reverse
Main Gear Shift	Full Synchronized 4 speeds
Range Selector	High - Low
Creeper Gear	Selector located on left of platform
Shuttle Selector	Synchronized, Forward - Reverse
Forward Speed Range	.1 - 14.3 MPH
Clutch	10.83" Dry Single Disc
Steering	Full Hydrostatic
Brakes	L & R Independent Oil Immersed Disc Brakes Parking Brake: Operated off of service brake
Differential Lock (rear)	Foot Actuated - Mechanical
Electrical System        Alternator	12V - 50 Amp
Battery	12V, 600 CCA
General Specifications	Dimensions with Standard Tire
Turning Radius	113.4" with brake/ 130.3" without brake
Length	137"
Width	65.2"
Height to top of ROPS	94"
Wheel Base	72.8"
Tire Sizes (Front/Rear)	9.5 x 20 (6 ply) / 13.6 x 28 (6 ply)
Weight with ROPS	4540 lbs.
Options	Canopy, Front Weights

 

LandTrac 530 DTC Specifications
Engine	Mitsubishi Indirect Injection Diesel Engine
Engine Horsepower	53 HP
Number of cylinders	4
Bore and Stroke	3.70" X 4.73"
Total Displacement	203.3 cubic inches
Rate Speed (rpm)	2500
Fuel Tank Capacity	14.5 gallons
Cold Weather Starting	Glow Plugs
Air Cleaner	Dry Type with Replaceable Cartridge
Power Take Off	540 RPM
PTO Horsepower	46
Operation	Independent or Manual/ Switch Operated
PTO Clutch	Electro-Hydraulic, Operated by switch on dash Panel
Shaft Diameter	1 3/8" (Six Spine)
Hydraulic System	Open Center
Flow gpm/psi	9.5 gpm/ 2400 psi
Lift Capacity	2976 lbs. @ 24" behind lower hitch pins
3 pt. Hitch Category	II
Controls	Position / Draft / Mixed
Remote Value (standard)	Double Spool/Double Acting -- with two sets of outlets
Transmission	8 Normal / 8 Creeper Forward -- 8 Normal / 8 Creeper Reverse
Main Gear Shift	Full Synchronized 4 speeds
Range Selector	High - Low
Creeper Gear	Selector located on left of platform
Shuttle Selector	Synchronized, Forward - Reverse
Forward Speed Range	.1 - 15.6 MPH
Clutch	10.83" Dry Single Disc
Steering	Full Hydrostatic
Brakes	L & R Independent Oil Immersed Disc Brakes Parking Brake: Operated off of service brake
Differential Lock (rear)	Foot Actuated - Mechanical
Electrical System        Alternator	12V - 50 Amp
Battery	12V, 600 CCA
General Specifications	Dimensions with Standard Tire
Turning Radius	120.1" with brake/ 138.9" without brake
Length	137"
Width	65.2"
Height to top of ROPS	94"
Wheel Base	77"
Tire Sizes (Front/Rear)	9.5 x 20 (6 ply) / 13.6 x 28 (6 ply)
Weight with ROPS	4610 lbs.
Options	Canopy, Front Weights

Used Equipment LandTrac Land Pride Tufline Toys Our Location E-mail us Home

Fewell Tractor Sales, Inc. Highways 421 & 55 P.O. Box 159 Campbellsburg, Kentucky 40011 Phone: (502) 532-7988 E-mail: sales@fewelltractor.com